{"id":5328,"date":"2026-11-21T06:05:49","date_gmt":"2026-11-21T06:05:49","guid":{"rendered":"https:\/\/www.kmdpower.com\/?p=5328"},"modified":"2026-11-21T06:05:51","modified_gmt":"2026-11-21T06:05:51","slug":"is-an-ac-inverter-draining-a-12v-100ah-solar-cctv-battery-before-the-cameras-do","status":"publish","type":"post","link":"https:\/\/www.kmdpower.com\/ro\/news\/is-an-ac-inverter-draining-a-12v-100ah-solar-cctv-battery-before-the-cameras-do\/","title":{"rendered":"Is an AC Inverter Draining a 12V 100Ah Solar CCTV Battery Before the Cameras Do?"},"content":{"rendered":"<p class=\"wp-block-paragraph\">Off-grid CCTV cameras may use only a few dozen watts, yet the battery empties faster than predicted. An overlooked load is the inverter and its AC adapters. <strong>Before adding another 12V 100Ah sodium-ion battery, measure AC-path watt-hours and verify voltage compatibility.<\/strong> DC may save energy; some equipment still needs AC.<\/p><p class=\"wp-block-paragraph\">Inverters draw power even at no AC load; peak efficiency does not establish low-load performance. Compare AC and qualified DC designs delivering <strong>the same uninterrupted service<\/strong> using DC-input Wh. First check voltage: the supplied Kamada Power sodium ion battery pack <strong>15.6V charging target exceeds the example SureSine Classic SI-300&#8217;s 15.5V input ceiling<\/strong>. Efficiency cannot justify an electrically incompatible pairing.<\/p><figure class=\"wp-block-image size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"1000\" height=\"1000\" src=\"https:\/\/www.kmdpower.com\/wp-content\/uploads\/Sodium-Battery-12V-100Ah-Bluetooth-Low-Temperature-Na-Ion-Battery-Supplier-Factory-Manufacturers-001.jpg\" alt=\"\" class=\"wp-image-1451\"\/><\/figure><p class=\"has-text-align-center alignwide wp-block-paragraph\"><strong><a href=\"https:\/\/www.kmdpower.com\/ro\/kamada-poewr-12v-100ah-sodium-ion-battery-product\/\" target=\"_blank\" rel=\"noreferrer noopener\">Kamada Power 12v 100Ah Baterie cu ioni de sodiu<\/a><\/strong><\/p><h2 class=\"wp-block-heading\">How Much Energy Can an Inverter Consume with No Camera Load?<\/h2><p class=\"wp-block-paragraph\">Morningstar&#8217;s <strong>SureSine Classic SI-300<\/strong> is a 300W, 12V-input off-grid inverter. Its published self-consumption is <strong>450mA ON with no AC load<\/strong>, <strong>55mA standby<\/strong> \u0219i <strong>25mA OFF<\/strong>, cu <strong>92% peak efficiency<\/strong> in the current datasheet. These model-specific figures are not <strong><a href=\"https:\/\/www.kmdpower.com\/ro\/\" target=\"_blank\" rel=\"noreferrer noopener\">Baterie Kamada Power<\/a><\/strong> test results. <a href=\"https:\/\/www.morningstarcorp.com\/products\/suresine-classic\/\" target=\"_blank\" rel=\"noreferrer noopener\">Morningstar Classic specifications<\/a>.<\/p><p class=\"wp-block-paragraph\">At an <em>assumed<\/em> 12V input, no-load ON draw is <strong>12V \u00d7 0.45A = 5.4W<\/strong>, sau <strong>129.6Wh in 24 hours<\/strong>\u2014more than a 5W device running all day (120Wh). Actual draw varies with voltage, mode and load.<\/p><figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>SureSine Classic state<\/th><th>Published DC current<\/th><th>Illustrative power at 12V<\/th><th>24h equivalent if continuously in this state<\/th><\/tr><\/thead><tbody><tr><td>Inverter ON, no AC load<\/td><td>450mA<\/td><td>5.40W<\/td><td><strong>129.6Wh<\/strong><\/td><\/tr><tr><td>\u00cen a\u0219teptare<\/td><td>55mA<\/td><td>0.66W<\/td><td><strong>15.8Wh<\/strong><\/td><\/tr><tr><td>Inverter OFF<\/td><td>25mA<\/td><td>0.30W<\/td><td><strong>7.2Wh<\/strong><\/td><\/tr><\/tbody><\/table><\/figure><p class=\"wp-block-paragraph\"><strong>Figure 1. Published currents converted to Wh at assumed 12V<\/strong>; not measured energy. Standby and OFF do not represent continuous AC CCTV service.<\/p><figure class=\"wp-block-image size-large\"><img decoding=\"async\" width=\"1024\" height=\"569\" src=\"https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_CCTV_AC_vs_DC_Energy_Chart-1024x569.png\" alt=\"\" class=\"wp-image-5329\" srcset=\"https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_CCTV_AC_vs_DC_Energy_Chart-1024x569.png 1024w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_CCTV_AC_vs_DC_Energy_Chart-300x167.png 300w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_CCTV_AC_vs_DC_Energy_Chart-768x427.png 768w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_CCTV_AC_vs_DC_Energy_Chart-18x10.png 18w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_CCTV_AC_vs_DC_Energy_Chart-600x333.png 600w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_CCTV_AC_vs_DC_Energy_Chart.png 1530w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><\/figure><p class=\"wp-block-paragraph\">\u00cen <strong>Always ON<\/strong> mode, AC stays available unless a fault occurs. In <strong>standby<\/strong>, the current Classic data indicates about <strong>8W<\/strong> to detect an AC load; the 2006 manual lists <strong>~8W for SI-300-220V and ~10W for SI-300-115V<\/strong>. Confirm the actual model\/revision before relying on standby: small CCTV loads may lose AC service. Always ON is the default. <a href=\"https:\/\/www.morningstarcorp.com\/wp-content\/uploads\/operation-manual-suresine-classic-en.pdf\" target=\"_blank\" rel=\"noreferrer noopener\">Morningstar Classic manual<\/a>.<\/p><p class=\"wp-block-paragraph\"><strong>Do not add 5.4W idle power to measured loaded DC input:<\/strong> it already includes inverter overhead.<\/p><h2 class=\"wp-block-heading\">Why Does a Small CCTV Load Make Inverter Efficiency Important?<\/h2><p class=\"wp-block-paragraph\">A 300W inverter supplying 25W runs at <strong>8.3% of rated output<\/strong>. Morningstar&#8217;s <a href=\"https:\/\/www.morningstarcorp.com\/wp-content\/uploads\/datasheet-suresine-classic-en.pdf\" target=\"_blank\" rel=\"noreferrer noopener\">Classic datasheet efficiency curve<\/a> shows efficiency varies with load; <strong>do not read a precise 25W efficiency from that plot<\/strong>. Fixed consumption, switching and adapters matter. <a href=\"https:\/\/www.energy.gov\/sites\/default\/files\/2018\/06\/f52\/94150c_Brown_050118-1100.pdf\" target=\"_blank\" rel=\"noreferrer noopener\">DOE\/LBNL AC\/DC research<\/a> likewise uses load-dependent curves, but does not prove CCTV savings.<\/p><p class=\"wp-block-paragraph\">Camera loads also vary. <a href=\"https:\/\/whitepapers.axis.com\/en-us\/typical-and-maximum-power-consumption-in-axis-cameras\" target=\"_blank\" rel=\"noreferrer noopener\">Axis&#8217;s December 2025 white paper<\/a> gives one example with <strong>4.7W typical (heater\/IR off)<\/strong> fa\u021b\u0103 de <strong>12.6W maximum<\/strong>. IR, heaters and motors change demand; those figures do not describe every camera.<\/p><p class=\"wp-block-paragraph\">An enclosure may also contain an NVR, router, PoE switch and adapters. Count the <strong>entire conversion chain<\/strong>, not only camera watts. The Classic manual lists <strong>95\u00b0C heatsink shutdown and 80\u00b0C recovery<\/strong>; check enclosure heat and thermal events. Some equipment requires AC.<\/p><h2 class=\"wp-block-heading\">How Much Battery Energy Does the AC Power Path Actually Use in 24 Hours?<\/h2><p class=\"wp-block-paragraph\">M\u0103sur\u0103 <strong>DC branch watt-hours<\/strong>, not inverter nameplate watts or AC volt-amperes (VA).<\/p><p class=\"wp-block-paragraph\">During battery-only discharge:<\/p><p class=\"wp-block-paragraph\"><strong>Battery discharge energy (Wh) = \u222b battery-terminal voltage (V) \u00d7 discharge current (A) dt<\/strong>, with time in hours; if in seconds, divide by <strong>3,600<\/strong>.<\/p><p class=\"wp-block-paragraph\">Meter the inverter&#8217;s <strong>DC input<\/strong> and its AC <em>real watts<\/em>. With PV on the bus, separately log inverter\/other branches, battery charge\/discharge and solar input; PV may power loads directly. Compare 24-hour paths delivering the <strong>same recorded service<\/strong>, including night operation.<\/p><h3 class=\"wp-block-heading\">An illustrative AC-versus-DC comparison<\/h3><p class=\"wp-block-paragraph\">Assume the <strong>same 25W useful CCTV load<\/strong> in two hypothetical architectures: <strong>36W DC input<\/strong> for inverter-plus-adapters versus <strong>29W<\/strong> for a qualified DC path. These are <em>planning assumptions<\/em>, not Morningstar or Kamada Power measurements.<\/p><figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Comparable quantity<\/th><th>AC inverter + AC adapters<\/th><th>Qualified DC supply<\/th><\/tr><\/thead><tbody><tr><td>Useful equipment power<\/td><td>25W<\/td><td>25W<\/td><\/tr><tr><td><strong>Assumed battery-side path input<\/strong><\/td><td><strong>36W<\/strong><\/td><td><strong>29W<\/strong><\/td><\/tr><tr><td>Path energy over 24 hours<\/td><td><strong>864Wh<\/strong><\/td><td><strong>696Wh<\/strong><\/td><\/tr><tr><td>Energy difference against AC design<\/td><td>-<\/td><td><strong>168Wh\/day less<\/strong><\/td><\/tr><\/tbody><\/table><\/figure><p class=\"wp-block-paragraph\"><strong>Figure 2 \u2014 Illustrative 24-hour energy for equivalent CCTV service<\/strong><\/p><figure class=\"wp-block-image size-large\"><img decoding=\"async\" width=\"1024\" height=\"569\" src=\"https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_Published_Inverter_Idle_Consumption_Chart-1024x569.png\" alt=\"\" class=\"wp-image-5330\" srcset=\"https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_Published_Inverter_Idle_Consumption_Chart-1024x569.png 1024w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_Published_Inverter_Idle_Consumption_Chart-300x167.png 300w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_Published_Inverter_Idle_Consumption_Chart-768x427.png 768w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_Published_Inverter_Idle_Consumption_Chart-18x10.png 18w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_Published_Inverter_Idle_Consumption_Chart-600x333.png 600w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-09_Published_Inverter_Idle_Consumption_Chart.png 1530w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><\/figure><p class=\"wp-block-paragraph\"><em>Illustrative inputs; 168Wh\/day is not measured battery saving. No-load draw is not counted twice.<\/em><\/p><p class=\"wp-block-paragraph\">A <strong>7W \u00d7 24h = 168Wh\/day<\/strong> reduction in path demand may reduce battery or solar demand, but usable Wh, recharge, temperature and cutoff still determine runtime.<\/p><h2 class=\"wp-block-heading\">Which CCTV Loads Can Safely Move from AC to Direct DC?<\/h2><p class=\"wp-block-paragraph\">Verifica\u021bi <strong>each device&#8217;s approved input<\/strong>, not just its wall plug. Cameras may use regulated DC or IEEE PoE, routers another voltage, and NVRs may require AC. Never bypass internal mains supplies or confuse passive and active PoE.<\/p><p class=\"wp-block-paragraph\">A DC redesign must cover the <strong>verified pack and charging voltage window<\/strong>, rail tolerance, startup\/IR\/heater peaks, protected wiring, grounding, cable loss, temperature and recovery. Meter DC-converter idle and loaded Wh too.<\/p><pre class=\"wp-block-code\"><code>EXISTING AC PATH                   POSSIBLE APPROVED DC PATH\n12V sodium-ion pack                 12V sodium-ion pack\n        |                                    |\n  DC-to-AC inverter                    Protected DC bus\n        |                                    |\n   AC adapter(s)                   Rated DC-DC \/ PoE supply\n        |                                    |\n CCTV \/ router \/ NVR                CCTV \/ router \/ NVR\n<\/code><\/pre><p class=\"wp-block-paragraph\"><em>Concept only, not an approved wiring diagram. Preserve protection and the required recording service.<\/em><\/p><h2 class=\"wp-block-heading\">Is the Runtime Shortfall Actually the Inverter or the Battery?<\/h2><p class=\"wp-block-paragraph\">Four causes can look alike: <strong>conversion overhead, insufficient usable Wh, a voltage-limit shutdown, or inadequate daily recharge<\/strong>.<\/p><p class=\"wp-block-paragraph\">Voltage compatibility is a <strong>veto<\/strong>, not an efficiency calculation. The <strong>SureSine Classic SI-300<\/strong> precizeaz\u0103 <strong>10.0\u201315.5V DC<\/strong>, cu <strong>15.5V high-voltage disconnect<\/strong> \u0219i <strong>14.5V reconnect<\/strong>. The supplied <strong>Kamada Power 12V 100Ah sodium ion battery datasheet<\/strong> precizeaz\u0103 <strong>12V nominal, 1,200Wh nominal, 15.6V maximum charging voltage and 8V discharge cutoff<\/strong>; its standard CC\/CV procedure reaches <strong>15.6V<\/strong>. If the Classic input sees that voltage, it <strong>exceeds the published limit<\/strong> and may disconnect AC. <strong>Reject a direct shared-bus pairing<\/strong> unless an approved design covers all operating states, tolerance and transients; cable drop is not overvoltage protection. The <a href=\"https:\/\/www.kmdpower.com\/ro\/kamada-poewr-12v-100ah-sodium-ion-battery-product\/\" target=\"_blank\" rel=\"noreferrer noopener\">Kamada Power 12v 100ah Baterie cu ioni de sodiu<\/a> shows a separate 12.8V model designation; never merge unconfirmed revisions. <a href=\"https:\/\/www.morningstarcorp.com\/wp-content\/uploads\/datasheet-suresine-classic-en.pdf\" target=\"_blank\" rel=\"noreferrer noopener\">Classic datasheet<\/a>.<\/p><p class=\"wp-block-paragraph\">Classic low-voltage choices are <strong>11.5V LVD \/ 12.6V reconnect<\/strong> (default) or <strong>10.5V \/ 11.6V<\/strong>. The published LVD delay is <strong>four minutes<\/strong>; an older Classic manual also lists <strong>10.0V instant LVD<\/strong>. Confirm the actual revision and capture both <strong>voltage and event timing<\/strong>, since startup sag and sustained undervoltage differ. Both selectable LVDs exceed the pack&#8217;s <strong>Deconectare de protec\u021bie la 8 V<\/strong>, not a normal service target. An inverter can stop early, but <strong>voltage thresholds alone cannot quantify remaining usable Wh<\/strong>. Check loaded voltage, temperature, BMS and restart; do not bypass protection.<\/p><p class=\"wp-block-paragraph\">The <strong>15.5V limit is Classic-specific<\/strong>. Morningstar&#8217;s <a href=\"https:\/\/www.morningstarcorp.com\/products\/suresine\/300-watts\/\" target=\"_blank\" rel=\"noreferrer noopener\">newer SureSine 300W<\/a> liste <strong>16.5V maximum<\/strong> for its 12V model, but needs separate qualification. Log daily charge\/discharge; Ah alone cannot cure a persistent deficit.<\/p><h2 class=\"wp-block-heading\">How Should an OEM Test Inverter Losses Before Ordering More 100Ah Packs?<\/h2><p class=\"wp-block-paragraph\">Use the actual battery, inverter, charger and CCTV BOM. Compare <strong>identical service and uptime<\/strong>.<\/p><ol class=\"wp-block-list\"><li><strong>Map power branches.<\/strong> Include DC\/AC, AC\/DC, PoE and loads outside the inverter.<\/li>\n\n<li><strong>Measure 24-hour energy.<\/strong> Separate inverter DC-input Wh, battery charge\/discharge Wh and PV input; synchronize with recording logs.<\/li>\n\n<li><strong>Check modes.<\/strong> Compare Always ON, standby and OFF; test the <strong>model-specific ~8\u201310W standby threshold<\/strong> with real loads. Sleeping is not continuous service.<\/li>\n\n<li><strong>Check voltage limits.<\/strong> Log charge maximum, <strong>LVD\/LVR<\/strong>, 4-minute delay, possible instant cutoff and transitions. Resolve the <strong>15.6V\/15.5V Classic conflict<\/strong> before approval.<\/li>\n\n<li><strong>Test the DC design.<\/strong> Verify outputs, PoE, startup, peaks, isolation and heat. Compare matched duty cycles; require <strong>no local recording gaps, resets or loss of required remote video<\/strong>, and log thermal protection.<\/li>\n\n<li><strong>Measure usable reserve.<\/strong> Use approved discharge limits, matched load\/temperature and BMS recovery; consider approved parallel packs <strong>only after<\/strong> energy balance and interfaces pass.<\/li><\/ol><p class=\"wp-block-paragraph\">Report <strong>path Wh, camera energy, usable pack Wh, voltage compatibility and recharge balance<\/strong> separately. Keep AC if DC fails safety or uptime requirements.<\/p><h2 class=\"wp-block-heading\">Should the OEM Change the Power Architecture or Buy Another Battery?<\/h2><figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Constatare verificat\u0103<\/th><th>Procurement decision<\/th><\/tr><\/thead><tbody><tr><td>AC path draws materially more energy for equivalent service; approved DC\/PoE interfaces pass<\/td><td><strong>Qualify direct DC first<\/strong>, then reassess storage<\/td><\/tr><tr><td>AC must stay, but low-load or Always ON losses are excessive<\/td><td>Evaluate a <strong>better-matched inverter<\/strong>, with qualified input voltage and continuous AC<\/td><\/tr><tr><td>Proposed Classic inverter may see <strong>15.6V<\/strong> above its <strong>15.5V<\/strong> limit<\/td><td><strong>Reject direct pairing or redesign<\/strong> the regulated input with manufacturer approval<\/td><\/tr><tr><td>Inverter LVD occurs before BMS cutoff<\/td><td>Coordinate authorized LVD\/LVR, measure usable Wh and verify recovery<\/td><\/tr><tr><td>Compatible AC path is necessary but verified usable Wh cannot meet autonomy<\/td><td>Consider <strong>approved parallel capacity<\/strong> if charging can restore it<\/td><\/tr><tr><td>PV replenishes less energy than the system consumes<\/td><td><strong>Correct daily energy deficit<\/strong>; more Ah postpones shutdown<\/td><\/tr><\/tbody><\/table><\/figure><p class=\"wp-block-paragraph\">AC-only recorders or isolation requirements may justify an inverter. Compare <strong>uptime, efficiency, safety, maintenance and cost<\/strong>.<\/p><h2 class=\"wp-block-heading\">What Should a Surveillance OEM Send for an Energy-Loss Review?<\/h2><p class=\"wp-block-paragraph\">Provide <strong>inverter model\/settings, CCTV BOM, battery\/PV Wh logs, charger, temperatures, uptime requirement and projected volume<\/strong>. Identify approved DC\/PoE inputs.<\/p><p class=\"wp-block-paragraph\">The <a href=\"https:\/\/www.kmdpower.com\/ro\/kamada-poewr-12v-100ah-sodium-ion-battery-product\/\" target=\"_blank\" rel=\"noreferrer noopener\">Kamada Power 12V 100Ah sodium-ion product<\/a> is a candidate, not a tested inverter pairing. Its <a href=\"https:\/\/www.kmdpower.com\/ro\/news\/12v-100ah-sodium-ion-battery-for-security-systems\/\" target=\"_blank\" rel=\"noreferrer noopener\">security-system applications guide<\/a> provides context; here the decision is <strong>avoidable AC-path Wh versus battery-voltage incompatibility<\/strong>.<\/p><h2 class=\"wp-block-heading\">\u00centreb\u0103ri frecvente<\/h2><h3 class=\"wp-block-heading\">Can an inverter drain a 12V 100Ah CCTV battery when no cameras are drawing power?<\/h3><p class=\"wp-block-paragraph\">Yes. Classic lists <strong>450mA ON\/no-load<\/strong>: <strong>129.6Wh\/day at assumed 12V<\/strong>. Standby\/OFF draw less but cannot be treated as uninterrupted service.<\/p><h3 class=\"wp-block-heading\">Is a 92% peak-efficient inverter 92% efficient at a 20W camera load?<\/h3><p class=\"wp-block-paragraph\">No. Use the manufacturer&#8217;s efficiency curve or meter DC input and AC real watts at that load. Do not double-count no-load draw.<\/p><h3 class=\"wp-block-heading\">Does switching to DC always extend CCTV runtime?<\/h3><p class=\"wp-block-paragraph\">No. A qualified DC\/PoE path must show <strong>lower measured Wh for identical uninterrupted service<\/strong> and satisfy input limits.<\/p><h3 class=\"wp-block-heading\">Will adding a second 12V 100Ah pack fix the inverter&#8217;s losses?<\/h3><p class=\"wp-block-paragraph\">Approved parallel packs add reserve, but do not fix conversion losses, the <strong>Classic 15.6V\/15.5V conflict<\/strong>, or a daily energy deficit.<\/p><h3 class=\"wp-block-heading\">Can inverter ECO mode maintain 24\/7 CCTV?<\/h3><p class=\"wp-block-paragraph\">Only if recording continues. Classic standby is approximately <strong>8W or 10W depending on model\/revision<\/strong>; verify the actual camera, router and NVR loads.<\/p><h2 class=\"wp-block-heading\">Concluzie<\/h2><p class=\"wp-block-paragraph\">An inverter can be a hidden load in small solar <strong><a href=\"https:\/\/www.kmdpower.com\/ro\/sodium-ion-battery-manufacturers\/\" target=\"_blank\" rel=\"noreferrer noopener\">CCTV Battery<\/a><\/strong> systems, but <strong>measured DC-input energy and uninterrupted service\u2014not idle current alone\u2014must guide procurement<\/strong>. The Classic&#8217;s 450mA no-load current is published; the 168Wh\/day AC\u2013DC difference is hypothetical. The supplied <strong><a href=\"https:\/\/www.kmdpower.com\/ro\/sodium-ion-battery-manufacturers\/\" target=\"_blank\" rel=\"noreferrer noopener\">Baterie cu ioni de sodiu Kamada Power<\/a><\/strong> pack&#8217;s <strong>15.6V charge target exceeds the SureSine Classic SI-300&#8217;s 15.5V ceiling<\/strong>. Resolve voltage compatibility, LVD timing and standby behavior before choosing direct DC, another inverter or more approved capacity. <a href=\"https:\/\/www.kmdpower.com\/ro\/contact-us\/\" target=\"_blank\" rel=\"noreferrer noopener\">Contacta\u021bi Kamada Power<\/a> with inverter settings, schematic, 24-hour Wh logs, temperature and projected annual volume for a revision-specific review.<\/p>","protected":false},"excerpt":{"rendered":"<p>Off-grid CCTV cameras may use only a few dozen watts, yet the battery empties faster than predicted. An overlooked load is the inverter and its AC adapters. Before adding another 12V 100Ah sodium-ion battery, measure AC-path watt-hours and verify voltage compatibility. DC may save energy; some equipment still needs AC. Inverters draw power even at&#8230;<\/p>","protected":false},"author":1,"featured_media":1451,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"rank_math_lock_modified_date":false,"_kad_post_transparent":"","_kad_post_title":"","_kad_post_layout":"","_kad_post_sidebar_id":"","_kad_post_content_style":"","_kad_post_vertical_padding":"","_kad_post_feature":"","_kad_post_feature_position":"","_kad_post_header":false,"_kad_post_footer":false,"footnotes":""},"categories":[19,26],"tags":[],"class_list":["post-5328","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-news_catalog","category-product-news"],"_links":{"self":[{"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/posts\/5328","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/comments?post=5328"}],"version-history":[{"count":1,"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/posts\/5328\/revisions"}],"predecessor-version":[{"id":5331,"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/posts\/5328\/revisions\/5331"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/media\/1451"}],"wp:attachment":[{"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/media?parent=5328"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/categories?post=5328"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.kmdpower.com\/ro\/wp-json\/wp\/v2\/tags?post=5328"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}