{"id":5325,"date":"2026-11-20T10:01:54","date_gmt":"2026-11-20T10:01:54","guid":{"rendered":"https:\/\/www.kmdpower.com\/?p=5325"},"modified":"2026-11-20T10:01:56","modified_gmt":"2026-11-20T10:01:56","slug":"why-does-a-solar-poe-switch-support-less-camera-power-from-a-12v-battery-than-from-24v","status":"publish","type":"post","link":"https:\/\/www.kmdpower.com\/ja\/news\/why-does-a-solar-poe-switch-support-less-camera-power-from-a-12v-battery-than-from-24v\/","title":{"rendered":"Why Does a Solar PoE Switch Support Less Camera Power from a 12V Battery Than from 24V?"},"content":{"rendered":"<p class=\"wp-block-paragraph\">Three IP cameras may have enough battery energy for the night, yet one is denied PoE power. Before expanding storage, check <strong>the switch&#8217;s voltage-specific PoE budget<\/strong> and port limits.<\/p><p class=\"wp-block-paragraph\">For example, Linovision rates its <strong>POE-SW804G-SOLAR at 60W total PoE on a 12V system and 120W on a 24V system<\/strong>. These ratings are model-specific. <strong>Parallel 12V batteries cannot unlock 120W mode.<\/strong> Check charging and startup separately.<\/p><figure class=\"wp-block-image size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"1000\" height=\"1000\" src=\"https:\/\/www.kmdpower.com\/wp-content\/uploads\/kamada-power-12v-100ah-sodium-ion-battery-main-image-002.jpg\" alt=\"\" class=\"wp-image-1181\"\/><\/figure><p class=\"has-text-align-center wp-block-paragraph\"><strong><a href=\"https:\/\/www.kmdpower.com\/ja\/kamada-poewr-12v-100ah-sodium-ion-battery-product\/\" target=\"_blank\" rel=\"noreferrer noopener\">\u30ab\u30de\u30c0\u30d1\u30ef\u30fc 12V 100ah \u30ca\u30c8\u30ea\u30a6\u30e0\u30a4\u30aa\u30f3\u30d0\u30c3\u30c6\u30ea\u30fc<\/a><\/strong><\/p><h2 class=\"wp-block-heading\">Does the Same Solar PoE Switch Really Have a Different 12V and 24V Power Budget?<\/h2><p class=\"wp-block-paragraph\">Yes. The <a href=\"https:\/\/support.linovision.com\/portal\/en\/kb\/articles\/poe-sw804g-solar-user-manual\" target=\"_blank\" rel=\"noreferrer noopener\">Linovision POE-SW804G-SOLAR \u53d6\u6271\u8aac\u660e\u66f8<\/a> specifies four IEEE 802.3af\/at PoE ports and the following system-voltage-dependent ratings:<\/p><figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Manufacturer-published specification<\/th><th>12V battery system<\/th><th>24V battery system<\/th><\/tr><\/thead><tbody><tr><td>Total PoE power budget<\/td><td><strong>60W<\/strong><\/td><td><strong>120W<\/strong><\/td><\/tr><tr><td>Maximum PV panel power specified for the system<\/td><td>170W<\/td><td>340W<\/td><\/tr><tr><td>Maximum PV open-circuit voltage<\/td><td>30V<\/td><td>60V<\/td><\/tr><tr><td>Maximum charging current<\/td><td>10A<\/td><td>10A<\/td><\/tr><tr><td>PoE port standard<\/td><td>IEEE 802.3af\/at<\/td><td>IEEE 802.3af\/at<\/td><\/tr><\/tbody><\/table><\/figure><p class=\"wp-block-paragraph\"><em>Source: Linovision manual. The 10A limit is for battery charging, not PoE output or pack discharge. The separate auxiliary-load limit is not the PoE budget.<\/em><\/p><p class=\"wp-block-paragraph\"><strong>Figure 1.<\/strong> Rated total PoE output at 12V and 24V; the 90W reference is a <strong>hypothetical three-camera PSE allocation<\/strong>, not a <strong><a href=\"https:\/\/www.kmdpower.com\/ja\/sodium-ion-battery-manufacturers\/\" target=\"_blank\" rel=\"noreferrer noopener\">\u30ab\u30de\u30c0\u30d1\u30ef\u30fc \u30ca\u30c8\u30ea\u30a6\u30e0\u30a4\u30aa\u30f3\u96fb\u6c60<\/a><\/strong> test.<\/p><figure class=\"wp-block-image size-large\"><img decoding=\"async\" width=\"1024\" height=\"587\" src=\"https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-08_Solar_PoE_12V_24V_Budget_Chart-1024x587.png\" alt=\"\" class=\"wp-image-5326\" srcset=\"https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-08_Solar_PoE_12V_24V_Budget_Chart-1024x587.png 1024w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-08_Solar_PoE_12V_24V_Budget_Chart-300x172.png 300w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-08_Solar_PoE_12V_24V_Budget_Chart-768x440.png 768w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-08_Solar_PoE_12V_24V_Budget_Chart-1536x880.png 1536w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-08_Solar_PoE_12V_24V_Budget_Chart-18x10.png 18w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-08_Solar_PoE_12V_24V_Budget_Chart-600x344.png 600w, https:\/\/www.kmdpower.com\/wp-content\/uploads\/V10-08_Solar_PoE_12V_24V_Budget_Chart.png 1824w\" sizes=\"(max-width: 1024px) 100vw, 1024px\" \/><\/figure><p class=\"wp-block-paragraph\">The 120W total is <strong>\u306a\u3044<\/strong> a per-port rating. Its IEEE 802.3af\/at ports cannot supply a camera requiring an IEEE 802.3bt high-power port. The <a href=\"https:\/\/ethernetalliance.org\/blog\/2022\/10\/17\/ethernet-alliance-poe-blog-sifos-app-note\/\" target=\"_blank\" rel=\"noreferrer noopener\">Ethernet Alliance&#8217;s PoE explanation<\/a> distinguishes up to <strong>30W at an 802.3at power-sourcing equipment (PSE) port<\/strong> from up to <strong>25.5W delivered to a powered device (PD)<\/strong> under standard conditions. Both individual ports and aggregate budget must pass.<\/p><h2 class=\"wp-block-heading\">Why Can 24V Support More PoE Power Without Changing the Cameras?<\/h2><p class=\"wp-block-paragraph\">At a given power and conversion efficiency, higher battery voltage means lower input current:<\/p><p class=\"wp-block-paragraph\"><strong>Battery-input current (A) \u2248 total PoE output power (W) \u00f7 [battery voltage (V) \u00d7 conversion efficiency].<\/strong><\/p><p class=\"wp-block-paragraph\">Current and heat can limit power, but Linovision does not disclose the exact cause. These are <strong>calculations, not measurements<\/strong>.<\/p><p class=\"wp-block-paragraph\">At an assumed <strong>85% efficiency<\/strong>, 60W from 12V needs <strong>about 5.9A<\/strong> of battery current; 120W from 24V also needs <strong>about 5.9A<\/strong>. Supplying 120W from 12V would need <strong>about 11.8A<\/strong> under the same assumption. Actual current changes with voltage and efficiency; the manufacturer&#8217;s <strong>60W 12V rating remains binding<\/strong>.<\/p><h2 class=\"wp-block-heading\">How Much PoE Power Do the Cameras Need at the Same Time?<\/h2><p class=\"wp-block-paragraph\">Typical camera consumption is not enough for power allocation. Axis&#8217;s <a href=\"https:\/\/whitepapers.axis.com\/en-us\/typical-and-maximum-power-consumption-in-axis-cameras\" target=\"_blank\" rel=\"noreferrer noopener\">December 2025 white paper<\/a> explains why IR, heaters, motors and other functions change maximum consumption. Check the exact camera&#8217;s <strong>PoE standard, negotiated or reserved PSE power, maximum demand and operating modes<\/strong>.<\/p><figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Proposed camera configuration<\/th><th>Illustrative PSE allocation<\/th><th>60W budget at 12V<\/th><th>120W budget at 24V<\/th><\/tr><\/thead><tbody><tr><td>Two cameras, each allocated 15.4W<\/td><td><strong>30.8W<\/strong><\/td><td>Potentially within budget<\/td><td>Potentially within budget<\/td><\/tr><tr><td>Three 802.3at cameras, each needing up to 30W at PSE<\/td><td><strong>90W<\/strong><\/td><td><strong>Exceeds budget<\/strong><\/td><td>Within budget; verify ports and conditions<\/td><\/tr><tr><td>One camera needing an IEEE 802.3bt 60W-class port<\/td><td>60W-class port needed<\/td><td><strong>Incompatible port<\/strong><\/td><td><strong>Incompatible port<\/strong><\/td><\/tr><\/tbody><\/table><\/figure><p class=\"wp-block-paragraph\"><em>Illustrative allocations, not equipment tests. Verify negotiation, firmware, port limits and cable losses.<\/em><\/p><p class=\"wp-block-paragraph\">Three cameras drawing about 20W each can exceed a 60W <strong>PSE allocation<\/strong> budget once classification, reservation and cable losses are considered.<\/p><p class=\"wp-block-paragraph\">If a third camera is denied power, inspect port allocation. For nighttime drops, log IR\/heater peaks. If <strong>all cameras reboot<\/strong>, check the DC bus, BMS, undervoltage and temperature before blaming PoE budget.<\/p><h2 class=\"wp-block-heading\">Why Does a Larger 12V 100Ah Sodium-Ion Battery Not Fix This Limit?<\/h2><p class=\"wp-block-paragraph\"><strong>Stored energy (Wh) is not the switch&#8217;s permitted output power (W).<\/strong> \u306b\u3064\u3044\u3066 <strong>Kamada Power 12V 100Ah sodium-ion battery datasheet supplied for this review<\/strong> \u3092\u6307\u5b9a\u3057\u307e\u3059 <strong>12V nominal, 1,200Wh nominal energy, 15.6V maximum charge voltage, 8V discharge cutoff and up to 100A continuous pack discharge<\/strong>. They neither raise the 60W rating nor prove usable Wh or loaded pack voltage.<\/p><p class=\"wp-block-paragraph\">\u306b\u3064\u3044\u3066 <strong>8V discharge cutoff is not a CCTV operating target<\/strong>. Verify the switch&#8217;s low-voltage disconnect, wiring drop and BMS recovery. Linovision re quires a <strong>12V battery above 9V to start the controller<\/strong>. A low-voltage shutdown needs a validated recovery path; sunlight alone does not guarantee restart.<\/p><p class=\"wp-block-paragraph\">Linovision\u306e <a href=\"https:\/\/support.linovision.com\/portal\/en\/kb\/articles\/poe-sw804g-solar-quick-guide\" target=\"_blank\" rel=\"noreferrer noopener\">4S LiFePO4 reference profile<\/a> \u30ea\u30b9\u30c8 <strong>14.4V boost, 14.2V float, 15.0V overvoltage protection and 0.5A end current<\/strong>. The supplied Kamada Power datasheet describes <strong>20A CC to 15.6V, then CV to 2A at 0\u201345\u00b0C<\/strong>. \u3053\u308c\u3089\u306f <strong>not matching approved charging profiles<\/strong>. The 14.4V target may undercharge this pack; the reference 15.0V protection point is below its standard charge target. Linovision&#8217;s <strong>10A charger limit<\/strong> is below Kamada Power 20A standard rate but is not inherently unsafe or incompatible if the pack maker approves a lower charge current. Temperature restrictions still apply.<\/p><p class=\"wp-block-paragraph\">For a battery other than the default <strong>12V LiFePO4<\/strong>, Linovision requires a <strong>separately sold RS485-to-USB cable and LINOVISION Tool Box<\/strong> to configure parameters <strong>after connecting the battery and before connecting PV<\/strong>. Confirm the exact firmware supports the pack maker&#8217;s approved voltage, charge termination, float behavior, temperature protection and recovery settings. Adjustable parameters do <strong>\u306a\u3044<\/strong> prove sodium-ion compatibility. Never bypass protection to force a match.<\/p><p class=\"wp-block-paragraph\">The separate <a href=\"https:\/\/www.kmdpower.com\/ja\/kamada-poewr-12v-100ah-sodium-ion-battery-product\/\" target=\"_blank\" rel=\"noreferrer noopener\">\u30ab\u30de\u30c0\u30d1\u30ef\u30fc 12V 100Ah \u30ca\u30c8\u30ea\u30a6\u30e0\u30a4\u30aa\u30f3\u30d0\u30c3\u30c6\u30ea\u30fc<\/a> uses a 12.8V model designation; do not combine unconfirmed revisions. Even <strong>manufacturer-approved parallel 12V packs<\/strong> increase possible reserve without changing nominal bank voltage or unlocking the switch&#8217;s 24V PoE budget.<\/p><p class=\"wp-block-paragraph\">Do not series-connect 12V packs without explicit approval. A <strong>12-to-24V booster on an all-in-one MPPT battery port<\/strong> may disrupt charging or system detection. A separate 24V power path requires independent qualification.<\/p><h2 class=\"wp-block-heading\">What Other Limits Can Cause a Camera to Be Denied PoE Power?<\/h2><p class=\"wp-block-paragraph\"><strong>Per-port capability.<\/strong> IEEE 802.3af\/at is not 802.3bt. A 120W aggregate budget does not convert a 30W-class port into a 60W-class one. Verify each camera&#8217;s required PoE type.<\/p><p class=\"wp-block-paragraph\"><strong>Power allocation or negotiation.<\/strong> A PSE may reserve power by class or communicated request. <a href=\"https:\/\/www.cisco.com\/c\/en\/us\/td\/docs\/switches\/lan\/c9000\/infra\/poe\/poe-configuration-guide\/g-poe\/r-guidelines-for-poe.html\" target=\"_blank\" rel=\"noreferrer noopener\">Cisco&#8217;s PoE guidelines<\/a> document budget-dependent allocation and denial, but <strong>do not establish Linovision&#8217;s firmware algorithm<\/strong>. Check this switch&#8217;s actual logs and LEDs.<\/p><p class=\"wp-block-paragraph\"><strong>Common input undervoltage.<\/strong> Controller LVD, converter input limits or BMS discharge interruption may take several cameras down at once. Log pack and switch-input voltage with protection status. The <strong>8V pack cutoff is not an approved controller LVD<\/strong>.<\/p><p class=\"wp-block-paragraph\"><strong>Temperature and startup.<\/strong> Test simultaneous IR, PTZ, heaters and restarts. Determine which event failed first rather than assuming every outage is a PoE budget issue.<\/p><p class=\"wp-block-paragraph\"><strong>Output operating mode.<\/strong> Linovision documents manual, light-controlled and scheduled load modes. Verify which mode affects the <strong>PoE ports versus the auxiliary LOAD output<\/strong>, and confirm the selected configuration supports <strong>24\/7 CCTV<\/strong>, not nighttime-only lighting.<\/p><p class=\"wp-block-paragraph\"><strong>Charging compatibility.<\/strong> Passing the 60W output test does not approve the MPPT. Verify the pack&#8217;s <strong>15.6V charging specification<\/strong>, current limits and controller settings independently.<\/p><h2 class=\"wp-block-heading\">How Should an OEM Qualify a 12V sodium-ion Battery and Solar PoE Switch?<\/h2><p class=\"wp-block-paragraph\">Freeze the hardware BOM: exact switch and firmware, cameras, Ethernet runs, charger profile, <strong><a href=\"https:\/\/www.kmdpower.com\/ja\/sodium-ion-battery-manufacturers\/\" target=\"_blank\" rel=\"noreferrer noopener\">\u30ab\u30de\u30c0\u30d1\u30ef\u30fc \u30ca\u30c8\u30ea\u30a6\u30e0\u30a4\u30aa\u30f3\u96fb\u6c60<\/a> pack\/BMS revision<\/strong>, site temperatures and expected duty cycle.<\/p><p class=\"wp-block-paragraph\"><strong>1. Screen total power.<\/strong> Sum the camera <strong>maximum or negotiated PSE allocations<\/strong>. If the design requires <strong>90W<\/strong>, it fails the present switch&#8217;s <strong>60W 12V total<\/strong> regardless of battery Ah.<\/p><p class=\"wp-block-paragraph\"><strong>2. Check each port.<\/strong> Confirm IEEE 802.3af\/at compatibility, per-port class, allocated power, wiring and cable losses; reject unsupported 802.3bt demands.<\/p><p class=\"wp-block-paragraph\"><strong>3. Verify battery and MPPT compatibility.<\/strong> \u78ba\u8a8d <strong>15.6V\u306e\u5145\u96fb\u76ee\u6a19\u5024<\/strong>, current and temperature limits, <strong>8V pack cutoff<\/strong>, LVD\/LVR and <strong>&gt;9V controller startup<\/strong>. Follow Linovision&#8217;s RS485-to-USB\/Tool Box setup procedure for non-default chemistry <strong>before PV connection<\/strong>, then confirm that firmware can implement the <strong>manufacturer-approved<\/strong> settings. Hold approval if it cannot.<\/p><p class=\"wp-block-paragraph\"><strong>4. Run all cameras together.<\/strong> Include IR, heaters, PTZ and routers; log PoE allocations, battery V\/I, input voltage, BMS events and temperature. Verify <strong>24-hour PoE\/LOAD output behavior<\/strong> under the selected manual, light or schedule mode, and check continuous recording.<\/p><p class=\"wp-block-paragraph\"><strong>5. Diagnose the first constraint.<\/strong> A denied <strong>third port<\/strong> suggests allocation or port limits; <strong>all cameras resetting<\/strong> suggests common-bus or protection events; <strong>regular timed shutdowns<\/strong> suggest output-mode settings. After low-voltage shutdown, verify automatic BMS\/controller recovery. Confirm with logs.<\/p><p class=\"wp-block-paragraph\"><strong>6. Record power and procurement decisions.<\/strong> A constant <strong>60W PoE output for 24h needs 1,440Wh at the PSE output<\/strong>, before conversion losses\u2014more than this pack&#8217;s <strong>\u516c\u79f0\u30a8\u30cd\u30eb\u30ae\u30fc\uff1a1,200Wh<\/strong> without daytime replenishment. Actual duty cycle, usable battery Wh and PV recharge determine autonomy. Choose <strong>keep 12V \/ change PoE device \/ engineer 24V \/ reject<\/strong>, recording outstanding tests.<\/p><p class=\"wp-block-paragraph\">Do not force BMS trips, exceed controller ratings or bypass the equipment&#8217;s safeguards.<\/p><h2 class=\"wp-block-heading\">Should the Project Keep 12V, Change PoE Hardware, or Move to 24V?<\/h2><p class=\"wp-block-paragraph\"><strong>Keep the existing 12V arrangement<\/strong> when allocations fit <strong>60W<\/strong>, each port and the approved battery\/charger settings pass, the output mode supports required uptime, and recovery tests succeed. Approved parallel expansion adds reserve, not PoE output rating.<\/p><p class=\"wp-block-paragraph\"><strong>Keep 12V but change the PoE device<\/strong> when the project needs, for example, <strong>90W of PSE allocation<\/strong> and a different switch can deliver that budget from an actual <strong>12V input<\/strong>, with an approved charging architecture. This can avoid unnecessarily replacing the complete battery system.<\/p><p class=\"wp-block-paragraph\"><strong>Consider a properly engineered 24V architecture<\/strong> when camera demand and available equipment justify it. Requalify the 24V battery or bank, charger\/MPPT, PV voltage, protection and startup. <strong>Do not assume two 12V sodium-ion packs can be connected in series.<\/strong><\/p><p class=\"wp-block-paragraph\"><strong>Reject the combination<\/strong> if a camera needs an unsupported PoE port, the required power exceeds available hardware ratings without a viable redesign, or the battery charging and recovery requirements cannot be met safely.<\/p><p class=\"wp-block-paragraph\">\u938c\u7530\u30d1\u30ef\u30fc <a href=\"https:\/\/www.kmdpower.com\/ja\/news\/12v-100ah-sodium-ion-battery-for-security-systems\/\" target=\"_blank\" rel=\"noreferrer noopener\">existing security-system application guide<\/a> covers battery use more broadly. Here the procurement decision is <strong>whether this particular PoE switch can supply the simultaneous cameras from the chosen 12V pack, without an incompatible charger or recovery path<\/strong>.<\/p><h2 class=\"wp-block-heading\">What Should a Surveillance OEM Send Before Selecting the Battery?<\/h2><p class=\"wp-block-paragraph\">Send the <strong>switch firmware, camera maximum PoE allocations, port map, MPPT settings, output operating mode, pack revision, site temperatures and annual volume<\/strong>. State whether 12V and 24\/7 unattended recovery are required.<\/p><p class=\"wp-block-paragraph\">\u306b\u3064\u3044\u3066 <a href=\"https:\/\/www.kmdpower.com\/ja\/kamada-poewr-12v-100ah-sodium-ion-battery-product\/\" target=\"_blank\" rel=\"noreferrer noopener\">\u30ab\u30de\u30c0\u30d1\u30ef\u30fc 12V 100Ah \u30ca\u30c8\u30ea\u30a6\u30e0\u30a4\u30aa\u30f3\u30d0\u30c3\u30c6\u30ea\u30fc<\/a> does not prove this switch\/pack pairing. Provide the exact datasheet and wiring schematic.<\/p><h2 class=\"wp-block-heading\">\u3088\u304f\u3042\u308b\u3054\u8cea\u554f<\/h2><h3 class=\"wp-block-heading\">Does a 120W PoE budget mean one camera can receive 120W?<\/h3><p class=\"wp-block-paragraph\">No. Total budget and per-port capability are separate. This model uses IEEE 802.3af\/at, not an IEEE 802.3bt high-power port.<\/p><h3 class=\"wp-block-heading\">Can a fully charged 12V sodium-ion battery make a 60W switch supply 90W?<\/h3><p class=\"wp-block-paragraph\">No. Battery state of charge and 100Ah capacity cannot override the switch&#8217;s <strong>60W total PoE rating at 12V<\/strong>.<\/p><h3 class=\"wp-block-heading\">Why do my cameras work individually but not all at once?<\/h3><p class=\"wp-block-paragraph\">Their combined PoE allocations may exceed the budget, or a single port may be incompatible. Check port logs first; if all cameras reboot together, also measure common DC voltage, temperature and BMS\/controller state.<\/p><h3 class=\"wp-block-heading\">Will two approved parallel 12V 100Ah packs unlock the 24V power rating?<\/h3><p class=\"wp-block-paragraph\">No. Manufacturer-approved parallel packs remain a nominal 12V bank. They may extend runtime or reduce sag, but <strong>the same switch stays rated for 60W at 12V<\/strong>.<\/p><h3 class=\"wp-block-heading\">Can I use a 12-to-24V boost converter to obtain the 120W rating?<\/h3><p class=\"wp-block-paragraph\">Not by feeding boosted voltage into the integrated MPPT battery input. A separate higher-voltage PoE power path might be engineered, but only with appropriate switch input ratings, isolation, protection and battery\/charger approval.<\/p><h2 class=\"wp-block-heading\">\u7d50\u8ad6<\/h2><p class=\"wp-block-paragraph\">The same solar PoE switch may have <strong>different total camera-power ratings at 12V and 24V<\/strong>. For Linovision&#8217;s POE-SW804G-SOLAR, these are <strong>60W versus 120W<\/strong>, with unchanged IEEE 802.3af\/at per-port limits. More <strong>12V battery capacity cannot raise the 60W ceiling<\/strong>. Verify camera allocations, the <strong><a href=\"https:\/\/www.kmdpower.com\/ja\/\" target=\"_blank\" rel=\"noreferrer noopener\">\u938c\u7530\u30d1\u30ef\u30fc<\/a> 15.6V charge profile<\/strong>, non-default battery configuration, <strong>>9V startup<\/strong>, continuous output mode and daily energy balance. Keep 12V with compatible PoE hardware, qualify a different 24V architecture, or reject the pairing. <a href=\"https:\/\/www.kmdpower.com\/ja\/contact-us\/\" target=\"_blank\" rel=\"noreferrer noopener\">\u938c\u7530\u30d1\u30ef\u30fc\u3078\u306e\u304a\u554f\u3044\u5408\u308f\u305b<\/a> with the camera list, firmware, charging settings, wiring and planned volume for a revision-specific review.<\/p>","protected":false},"excerpt":{"rendered":"<p>Three IP cameras may have enough battery energy for the night, yet one is denied PoE power. Before expanding storage, check the switch&#8217;s voltage-specific PoE budget and port limits. For example, Linovision rates its POE-SW804G-SOLAR at 60W total PoE on a 12V system and 120W on a 24V system. These ratings are model-specific. Parallel 12V&#8230;<\/p>","protected":false},"author":1,"featured_media":1181,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"rank_math_lock_modified_date":false,"_kad_post_transparent":"","_kad_post_title":"","_kad_post_layout":"","_kad_post_sidebar_id":"","_kad_post_content_style":"","_kad_post_vertical_padding":"","_kad_post_feature":"","_kad_post_feature_position":"","_kad_post_header":false,"_kad_post_footer":false,"footnotes":""},"categories":[19,26],"tags":[],"class_list":["post-5325","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-news_catalog","category-product-news"],"_links":{"self":[{"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/posts\/5325","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/comments?post=5325"}],"version-history":[{"count":1,"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/posts\/5325\/revisions"}],"predecessor-version":[{"id":5327,"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/posts\/5325\/revisions\/5327"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/media\/1181"}],"wp:attachment":[{"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/media?parent=5325"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/categories?post=5325"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.kmdpower.com\/ja\/wp-json\/wp\/v2\/tags?post=5325"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}